WindContPType3IEC Class
P control model type 3. Reference: IEC 61400-27-1:2015, 5.6.5.4.
Diagram
Свойства (25)
| ID | Тип | Описание | Количество |
|---|---|---|---|
| dpmax | PU | Maximum wind turbine power ramp rate (<i>dp</i><i><sub>max</sub></i>). It is a type-dependent parameter. | 1..1 |
| dprefmax | PU | Maximum ramp rate of wind turbine reference power (<i>dp</i><i><sub>refmax</sub></i>). It is a project-dependent parameter. | 1..1 |
| dprefmin | PU | Minimum ramp rate of wind turbine reference power (<i>dp</i><i><sub>refmin</sub></i>). It is a project-dependent parameter. | 1..1 |
| dthetamax | PU | Ramp limitation of torque, required in some grid codes (<i>dt</i><i><sub>max</sub></i>). It is a project-dependent parameter. | 1..1 |
| dthetamaxuvrt | PU | Limitation of torque rise rate during UVRT (<i>dtheta</i><i><sub>maxUVRT</sub></i>). It is a project-dependent parameter. | 1..1 |
| kdtd | PU | Gain for active drive train damping (<i>K</i><i><sub>DTD</sub></i>). It is a type-dependent parameter. | 1..1 |
| kip | PU | PI controller integration parameter (<i>K</i><sub>Ip</sub>). It is a type-dependent parameter. | 1..1 |
| kpp | PU | PI controller proportional gain (<i>K</i><sub>Pp</sub>). It is a type-dependent parameter. | 1..1 |
| mpuvrt | Boolean | Enable UVRT power control mode (<i>M</i><i><sub>pUVRT</sub></i><sub>)</sub>. It is a project-dependent parameter. true = voltage control (1 in the IEC model) false = reactive power control (0 in the IEC model). | 1..1 |
| omegaoffset | PU | Offset to reference value that limits controller action during rotor speed changes (<i>omega</i><i><sub>offset</sub></i>). It is a case-dependent parameter. | 1..1 |
| pdtdmax | PU | Maximum active drive train damping power (<i>p</i><sub>DTDmax</sub>). It is a type-dependent parameter. | 1..1 |
| tdvs | Seconds | Time<sub> </sub>delay after deep voltage sags (<i>T</i><i><sub>DVS</sub></i>) (>= 0). It is a project-dependent parameter. | 1..1 |
| thetaemin | PU | Minimum electrical generator torque (<i>t</i><sub>emin</sub>). It is a type-dependent parameter. | 1..1 |
| thetauscale | PU | Voltage scaling factor of reset-torque (<i>t</i><sub>uscale</sub>). It is a project-dependent parameter. | 1..1 |
| tomegafiltp3 | Seconds | Filter time constant for generator speed measurement (<i>T</i><sub>omegafiltp3</sub>) (>= 0). It is a type-dependent parameter. | 1..1 |
| tpfiltp3 | Seconds | Filter time constant for power measurement (<i>T</i><sub>pfiltp3</sub>) (>= 0). It is a type-dependent parameter. | 1..1 |
| tpord | PU | Time constant in power order lag (<i>T</i><sub>pord</sub>). It is a type-dependent parameter. | 1..1 |
| tufiltp3 | Seconds | Filter time constant for voltage measurement (<i>T</i><sub>ufiltp3</sub>) (>= 0). It is a type-dependent parameter. | 1..1 |
| tomegaref | Seconds | Time constant in speed reference filter (<i>T</i><sub>omega,ref</sub>) (>= 0). It is a type-dependent parameter. | 1..1 |
| udvs | PU | Voltage limit for hold UVRT status after deep voltage sags (<i>u</i><i><sub>DVS</sub></i>). It is a project-dependent parameter. | 1..1 |
| updip | PU | Voltage dip threshold for P-control (<i>u</i><sub>Pdip</sub>). Part of turbine control, often different (e.g 0.8) from converter thresholds. It is a project-dependent parameter. | 1..1 |
| omegadtd | PU | Active drive train damping frequency (<i>omega</i><i><sub>DTD</sub></i>). It can be calculated from two mass model parameters. It is a type-dependent parameter. | 1..1 |
| zeta | Float | Coefficient for active drive train damping (<i>zeta</i>). It is a type-dependent parameter. | 1..1 |
| WindTurbineType3IEC | WindTurbineType3IEC | Wind turbine type 3 model with which this wind control P type 3 model is associated. | 1 |
| WindDynamicsLookupTable | WindDynamicsLookupTable | The wind dynamics lookup table associated with this P control type 3 model. | 1..n |
Ссылки (2)
| Класс | Свойство | Описание |
|---|---|---|
| cim:WindTurbineType3IEC | cim:WindContPType3IEC |
Wind control P type 3 model associated with this wind turbine type 3 model. |
| cim:WindDynamicsLookupTable | cim:WindContPType3IEC |
The P control type 3 model with which this wind dynamics lookup table is associated. |
Информация о классе
- ID
cim:WindContPType3IEC- Тип
- Class
- Наследует
- cim:IdentifiedObject
- Свойств
- 25