Seconds Data Type

An automatic voltage regulation delay (AVRDelay) which is the time delay from a change in voltage to when the capacitor is allowed to change state. This filters out temporary changes in voltage.

Inertia constant of generator or motor and mechanical load (<i>H</i>) (&gt; 0). This is the specification for the stored energy in the rotating mass when operating at rated speed. For a generator, this includes the generator plus all other elements (turbine, exciter) on the same shaft and has units of MW x s. For a motor, it includes the motor plus its mechanical load. Conventional units are PU on the generator MVA base, usually expressed as MW x s / MVA or just s. This value is used in the accelerating power reference frame for operator training simulator solutions. Typical value = 3.

Direct-axis transient rotor time constant (<i>T'do</i>) (&gt; SynchronousMachineTimeConstantReactance.tppdo). Typical value = 5.

Direct-axis subtransient rotor time constant (<i>T''do</i>) (&gt; 0). Typical value = 0,03.

Quadrature-axis transient rotor time constant (<i>T'qo</i>) (&gt; SynchronousMachineTimeConstantReactance.tppqo). Typical value = 0,5.

Quadrature-axis subtransient rotor time constant (<i>T''qo</i>) (&gt; 0). Typical value = 0,03.

Damping time constant for “Canay” reactance (&gt;= 0). Typical value = 0.

Transient rotor time constant (<i>T'o</i>) (&gt; AsynchronousMachineTimeConstantReactance.tppo). Typical value = 5.

Subtransient rotor time constant (<i>T''o</i>) (&gt; 0). Typical value = 0,03.

Governor lag time constant (<i>T1</i>) (&gt;= 0). Typical value = 0,25.

Governor lead time constant (<i>T2)</i> (&gt;= 0). Typical value = 0.

Gate actuator time constant (<i>T3</i>) (&gt;= 0). Typical value = 0,1.

Water starting time (<i>T4</i>) (&gt;= 0).

Gate servo time constant (<i>Tg</i>) (&gt;= 0). Typical value = 0,5.

Pilot servo valve time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0,03.

Dashpot time constant (<i>Tr</i>) (&gt;= 0). Typical value = 12.

Water inertia time constant (<i>Tw</i>) (&gt;= 0). Typical value = 2.

Governor lag time constant (<i>T1</i>) (&gt;= 0). Typical value = 0.

Governor lead time constant (<i>T2</i>) (&gt;= 0). Typical value = 0.

Valve positioner time constant (<i>T3</i>) (&gt; 0). Typical value = 0,1.

Inlet piping/steam bowl time constant (<i>T4</i>) (&gt;= 0). Typical value = 0,3.

Time constant of second boiler pass (<i>T5</i>) (&gt;= 0). Typical value = 5.

Time constant of third boiler pass (<i>T6</i>) (&gt;= 0). Typical value = 0,5.

Time constant of fourth boiler pass (<i>T7</i>) (&gt;= 0). Typical value = 0.

Electrical power transducer time constant (<i>Tpelec</i>) (&gt; 0). Typical value = 1.

Governor derivative controller time constant (<i>Tdgov</i>) (&gt;= 0). Typical value = 1.

Actuator time constant (<i>Tact</i>) (&gt;= 0). Typical value = 0,5.

Turbine lag time constant (<i>Tb</i>) (&gt; 0). Typical value = 0,5.

Turbine lead time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0.

Transport time delay for diesel engine used in representing diesel engines where there is a small but measurable transport delay between a change in fuel flow setting and the development of torque (<i>Teng</i>) (&gt;= 0). <i>Teng</i> should be zero in all but special cases where this transport delay is of particular concern. Typical value = 0.

Load-limiter time constant (<i>Tfload</i>) (&gt; 0). Typical value = 3.

Acceleration limiter time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,1.

Temperature detection lead time constant (<i>Tsa</i>) (&gt;= 0). Typical value = 4.

Temperature detection lag time constant (<i>Tsb</i>) (&gt;= 0). Typical value = 5.

Electrical power transducer time constant (<i>Tpelec</i>) (&gt;= 0). Typical value = 2,5.

Governor derivative controller time constant (<i>Tdgov</i>) (&gt;= 0). Typical value = 1.

Actuator time constant (<i>Tact</i>) (&gt;= 0). Typical value = 0,4.

Turbine lag time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0,1.

Turbine lead time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0.

Transport time delay for diesel engine used in representing diesel engines where there is a small but measurable transport delay between a change in fuel flow setting and the development of torque (<i>Teng</i>) (&gt;= 0). <i>Teng</i> should be zero in all but special cases where this transport delay is of particular concern. Typical value = 0.

Load limiter time constant (<i>Tfload</i>) (&gt;= 0). Typical value = 3.

Acceleration limiter time constant (<i>Ta</i>) (&gt;= 0). Typical value = 1.

Temperature detection lead time constant (<i>Tsa</i>) (&gt;= 0). Typical value = 0.

Temperature detection lag time constant (<i>Tsb</i>) (&gt;= 0). Typical value = 50.

Governor mechanism time constant (<i>T1</i>) (&gt;= 0). <i>T1</i> represents the natural valve positioning time constant of the governor for small disturbances, as seen when rate limiting is not in effect. Typical value = 0,5.

Turbine power time constant (<i>T2</i>) (&gt;= 0). <i>T2</i> represents delay due to internal energy storage of the gas turbine engine. <i>T2</i> can be used to give a rough approximation to the delay associated with acceleration of the compressor spool of a multi-shaft engine, or with the compressibility of gas in the plenum of a free power turbine of an aero-derivative unit, for example. Typical value = 0,5.

Turbine exhaust temperature time constant (<i>T3</i>) (&gt;= 0). Typical value = 3.

Governor mechanism time constant (<i>T1</i>) (&gt;= 0). <i>T1</i> represents the natural valve positioning time constant of the governor for small disturbances, as seen when rate limiting is not in effect. Typical value = 0,5.

Turbine power time constant (<i>T2</i>) (&gt;= 0). <i>T2</i> represents delay due to internal energy storage of the gas turbine engine. <i>T2</i> can be used to give a rough approximation to the delay associated with acceleration of the compressor spool of a multi-shaft engine, or with the compressibility of gas in the plenum of the free power turbine of an aero-derivative unit, for example. Typical value = 0,5.

Turbine exhaust temperature time constant (<i>T3</i>) (&gt;= 0). <i>T3</i> represents delay in the exhaust temperature and load limiting system. Typical value = 3.

Valve position averaging time constant (<i>Tltr</i>) (&gt;= 0). Typical value = 10.

Governor lead time constant (<i>T4</i>) (&gt;= 0). Typical value = 0.

Governor lag time constant (<i>T5</i>) (&gt;= 0). If = 0, entire gain and lead-lag block is bypassed. Typical value = 0.

Governor lead time constant (<i>X</i>) (&gt;= 0).

Governor lag time constant (<i>Y</i>) (&gt; 0).

Turbine and exhaust delay (<i>Etd</i>) (&gt;= 0).

Compressor discharge time constant (<i>Tcd</i>) (&gt;= 0).

Fuel control time constant (<i>T</i>) (&gt;= 0).

Combustion reaction time delay (<i>Ecr</i>) (&gt;= 0).

Fuel system time constant (<i>Tf</i>) (&gt;= 0).

Radiation shield time constant (<i>T3</i>) (&gt;= 0).

Thermocouple time constant (<i>T4</i>) (&gt;= 0).

Temperature controller integration rate (<i>Tt</i>) (&gt;= 0).

Temperature control time constant (<i>T5</i>) (&gt;= 0).

Time constant of speed governor (<i>Tg</i>) (&gt;= 0). Typical value = 0,05.

Time constant of fuel valve positioner (<i>Ty</i>) (&gt;= 0). Typical value = 0,2.

Fuel control time constant (<i>Tac</i>) (&gt;= 0). Typical value = 0,1.

Compressor discharge volume time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0,2.

Time constant of radiation shield (<i>Tsi</i>) (&gt;= 0). Typical value = 15.

Time constant of thermocouple (<i>Ttc</i>) (&gt;= 0). Typical value = 2,5.

Temperature controller derivative gain (<i>Td</i>) (&gt;= 0). Typical value = 3,3.

Time constant of fuel valve positioner (<i>Ty</i>) (&gt;= 0). Typical value = 0,1.

Maximum gate opening velocity (<i>TA</i>) (&gt;= 0). Typical value = 3.

Maximum gate closing velocity (<i>TC</i>) (&gt;= 0). Typical value = 0,5.

Fuel control time constant (<i>Tcm</i>) (&gt;= 0). Typical value = 0,1.

Compressor discharge volume time constant (<i>Tm</i>) (&gt;= 0). Typical value = 0,2.

Turbine and exhaust delay (<i>Etd</i>) (&gt;= 0).

Compressor discharge time constant (<i>Tcd</i>) (&gt;= 0).

Fuel control time constant (<i>T</i>) (&gt;= 0).

Combustion reaction time delay (<i>Ecr</i>) (&gt;= 0).

Fuel system time constant (<i>Tf</i>) (&gt;= 0).

Radiation shield time constant (<i>T3</i>) (&gt;= 0).

Thermocouple time constant (<i>T4</i>) (&gt;= 0).

Temperature controller integration rate (<i>Tt</i>) (&gt;= 0).

Temperature control time constant (<i>T5</i>) (&gt;= 0).

Power transducer time constant (<i>Td</i>) (&gt;= 0).

Washout time constant (<i>Tr</i>) (&gt; 0). Typical value = 5.

Filter time constant (<i>Tf</i>) (&gt; 0). Typical value = 0,05.

Gate servo time constant (<i>Tg</i>) (&gt; 0). Typical value = 0,5.

Water inertia time constant (<i>Tw</i>) (&gt; 0). Typical value = 1.

Gate servo time constant (<i>Tg</i>) (&gt; 0). Typical value = 0,5.

Pilot servo valve time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0,03.

Dashpot time constant (<i>Tr</i>) (&gt;= 0). Typical value = 12.

Water inertia time constant (<i>Tw</i>) (&gt;= 0). Typical value = 2.

Input filter time constant (<i>Td</i>) (&gt;= 0). Typical value = 0,05.

Washout time constant (<i>Tf</i>) (&gt;= 0). Typical value = 0,1.

Gate servo time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0,05.

Power feedback time constant (<i>Tt</i>) (&gt;= 0). Typical value = 0,2.

Water inertia time constant (<i>Tw</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 1.

Gate servo time constant (<i>Tg</i>) (&gt; 0). Typical value = 0,5.

Pilot servo time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0,1.

Permanent droop (<i>Rperm</i>) (&gt;= 0). Typical value = 0,05.

Temporary droop (<i>Rtemp</i>) (&gt;= 0). Typical value = 0,3.

Dashpot time constant (<i>Tr</i>) (&gt;= 0). Typical value = 5.

Water inertia time constant (<i>Tw</i>) (&gt; 0). Typical value = 1.

Blade servo time constant (<i>Tblade</i>) (&gt;= 0). Typical value = 100.

Input filter time constant (<i>Td</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0.

Washout time constant (<i>Tf</i>) (&gt;= 0). Typical value = 0,1.

Gate servo time constant (<i>Tp</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0,35.

Turbine time constant (<i>Tturb</i>) (&gt;= 0). See parameter detail 3. Typical value = 0,8.

Power feedback time constant (<i>Tt</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0,02.

Derivative gain (<i>Ta</i>) (&gt;= 0). Typical value = 3.

Washout time constant (<i>Td</i>) (&gt;= 0). Typical value = 6.

Gate servo time constant (<i>Ts</i>) (&gt;= 0). Typical value = 0,5.

Water inertia time constant (<i>Twnc</i>) (&gt;= 0). Typical value = 1.

Water tunnel and surge chamber inertia time constant (<i>Twng</i>) (&gt;= 0). Typical value = 3.

Derivative feedback gain (<i>Tx</i>) (&gt;= 0). Typical value = 1.

Derivative gain (accelerometer time constant) (<i>Ta</i>) (&gt;= 0). Typical value = 3.

Gate servo time constant (<i>Ts</i>) (&gt;= 0). Typical value = 0,15.

Servomotor integrator time constant (<i>Tv</i>) (&gt;= 0). Typical value = 0,3.

Water inertia time constant (<i>Twnc</i>) (&gt;= 0). Typical value = 1.

Water tunnel and surge chamber inertia time constant (<i>Twng</i>) (&gt;= 0). Typical value = 3.

Electronic integrator time constant (<i>Tx</i>) (&gt;= 0). Typical value = 0,5.

Input filter time constant (<i>Td</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0.

Washout time constant (<i>Tf</i>) (&gt;= 0). Typical value = 0,1.

Gate servo time constant (<i>Tp</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0,35.

Turbine time constant (<i>Tturb</i>) (&gt;= 0). See Parameter detail 3. Typical value = 0,8.

Power feedback time constant (<i>Tt</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0,02.

Speed detector time constant (<i>Treg</i>) (&gt;= 0). Typical value = 0.

Controller time constant (<i>Ta</i>) (&gt;= 0). Typical value = 0.

Gate servo time constant (<i>Tb</i>) (&gt; 0).

Water inertia time constant (<i>Tw</i>) (&gt;= 0). Typical value = 0.

Input filter time constant (<i>Td</i>) (&gt;= 0). Typical value = 0,05.

Lead time constant 1 (<i>T1</i>) (&gt;= 0). Typical value = 1,5.

Lag time constant 1 (<i>T2</i>) (&gt;= 0). Typical value = 0,1.

Lead time constant 2 (<i>T3</i>) (&gt;= 0). Typical value = 1,5.

Lag time constant 2 (<i>T4</i>) (&gt;= 0). Typical value = 0,1.

Lead time constant 3 (<i>T5</i>) (&gt;= 0). Typical value = 0.

Lag time constant 3 (<i>T6</i>) (&gt;= 0). Typical value = 0,05.

Lead time constant 4 (<i>T7</i>) (&gt;= 0). Typical value = 0.

Lag time constant 4 (<i>T8</i>) (&gt;= 0). Typical value = 0,05.

Gate servo time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0,05.

Power feedback time constant (<i>Tt</i>) (&gt;= 0). Typical value = 0.

Water inertia time constant (<i>Tw</i>) (&gt; 0). Typical value = 1.

Electrical power droop time constant (<i>Tpe</i>) (&gt;= 0).

Derivative controller time constant (<i>Td</i>) (&gt;= 0). Limits the derivative characteristic beyond a breakdown frequency to avoid amplification of high-frequency noise.

Pilot valve time lag time constant (<i>Tp</i>) (&gt;= 0).

Distributive valve time lag time constant (<i>Tdv</i>) (&gt;= 0).

Value to allow the distribution valve controller to advance beyond the gate movement rate limit (<i>Tg</i>) (&gt;= 0).

Water inertia time constant (<i>Tw</i>) (&gt; 0).

Speed detector time constant (<i>Treg</i>) (&gt;= 0).

Controller time constant (<i>Ta</i>) (&gt;= 0). Typical value = 0.

Gate servo time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0.

Water inertia time constant (<i>Tw</i>) (&gt;= 0). Typical value = 0.

Steam bowl time constant (<i>T1</i>) (&gt; 0). Typical value = 0,5.

Numerator time constant of <i>T2</i>/<i>T3</i> block (<i>T2</i>) (&gt;= 0). Typical value = 3.

Reheater time constant (<i>T3</i>) (&gt; 0). Typical value = 10.

Governor lag time constant (<i>T1</i>) (&gt;= 0). Typical value = 0.

Governor lead time constant (<i>T2</i>) (&gt;= 0). Typical value = 0.

Valve positioner time constant (<i>T3) </i>(&gt; 0). Typical value = 0,1.

Inlet piping/steam bowl time constant (<i>T4</i>) (&gt;= 0). Typical value = 0,3.

Time constant of second boiler pass (<i>T5</i>) (&gt;= 0). Typical value = 5.

Time constant of third boiler pass (<i>T6</i>) (&gt;= 0). Typical value = 0,5.

Time constant of fourth boiler pass (<i>T7</i>) (&gt;= 0). Typical value = 0.

Governor lag time constant (<i>T</i><i>₁</i>) (&gt; 0). Typical value = 0,45.

Governor lead time constant (<i>T</i><i>₂</i>) (&gt;= 0). Typical value = 0.

Time constant (<i>T1</i>). Typical value = 0,05.

Time constant (<i>Tn</i>) (&gt; 0). Typical value = 1,0.

Time constant (<i>Td</i>) (&gt; 0). Typical value = 1,0.

Time constant (<i>T4</i>). Typical value = 0,15.

Time constant (<i>T5</i>). Typical value = 12,0.

Time constant (<i>T6</i>). Typical value = 0,75.

HP governor time constant (<i>T1hp</i>) (&gt;= 0). Typical value = 0,1.

HP turbine time constant (<i>T3hp</i>) (&gt;= 0). Typical value = 0,1.

HP turbine time constant (<i>T4hp</i>) (&gt;= 0). Typical value = 0,1.

HP reheater time constant (<i>T5hp</i>) (&gt;= 0). Typical value = 10.

LP governor time constant (<i>T1lp</i>) (&gt;= 0). Typical value = 0,1.

LP turbine time constant (<i>T3lp</i>) (&gt;= 0). Typical value = 0,1.

LP turbine time constant (<i>T4lp</i>) (&gt;= 0). Typical value = 0,1.

LP reheater time constant (<i>T5lp</i>) (&gt;= 0). Typical value = 10.

Power transducer time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0,07.

Integral time constant of the power controller (<i>Tip</i>) (&gt;= 0). Typical value = 2.

Derivative time constant of the power controller (<i>Tdp</i>) (&gt;= 0). Typical value = 0.

Time constant of the power controller (<i>Tfp</i>) (&gt;= 0). Typical value = 0.

Frequency transducer time constant (<i>Tf</i>) (&gt;= 0). Typical value = 0.

Electro hydraulic transducer (<i>Ten</i>) (&gt;= 0). Typical value = 0,1.

Speed transducer time constant (<i>Tw</i>) (&gt;= 0). Typical value = 0,02.

Control valves servo time constant (<i>Tvhp</i>) (&gt;= 0). Typical value = 0,1.

Intercept valves servo time constant (<i>Tvip</i>) (&gt;= 0). Typical value = 0,15.

High pressure (HP) time constant of the turbine (<i>Thp</i>) (&gt;= 0). Typical value = 0,31.

Reheater time constant of the turbine (<i>Trh</i>) (&gt;= 0). Typical value = 8.

Low pressure (LP) time constant of the turbine (<i>Tlp</i>) (&gt;= 0). Typical value = 0,45.

Boiler time constant (<i>Tb</i>) (&gt;= 0). Typical value = 100.

Governor time constant (<i>T1</i>) (&gt;= 0).

Reheater time constant (<i>T3</i>) (&gt;= 0).

Time constant with which power falls off after intercept valve closure (<i>Tt</i>) (&gt;= 0).

Time after initial time for valve to close (<i>Ta</i>) (&gt;= 0).

Time after initial time for valve to begin opening (<i>Tb</i>) (&gt;= 0).

Time after initial time for valve to become fully open (<i>Tc</i>) (&gt;= 0).

Governor lead time constant (<i>T1</i>) (&gt;= 0). Typical value = 0.

Governor lag time constant (<i>T2</i>) (&gt;= 0). Typical value = 0.

Valve positioner time constant (<i>T3</i>) (&gt; 0). Typical value = 0.

Inlet piping/steam bowl time constant (<i>T4</i>) (&gt;= 0). Typical value = 0,2.

Time constant of second boiler pass (i.e. reheater) (<i>T5</i>) (&gt; 0 if fast valving is used, otherwise &gt;= 0). Typical value = 0,5.

Time constant of crossover or third boiler pass (<i>T6</i>) (&gt;= 0). Typical value = 10.

Time to close intercept valve (IV) (<i>Ta</i>) (&gt;= 0). Typical value = 0,97.

Time until IV starts to reopen (<i>Tb</i>) (&gt;= 0). Typical value = 0,98.

Time until IV is fully open (<i>Tc</i>) (&gt;= 0). Typical value = 0,99.

Control valves rate opening time (<i>Ta</i>) (&gt;= 0). Typical value = 0,8.

Control valves rate closing time (<i>Tc</i>) (&gt;= 0). Typical value = 0,5.

Control valves servo time constant (<i>Ty</i>) (&gt;= 0). Typical value = 0,1.

Intercept valves rate opening time (<i>Tam</i>) (&gt;= 0). Typical value = 0,8.

Intercept valves rate closing time (<i>Tcm</i>) (&gt;= 0). Typical value = 0,5.

High pressure (HP) time constant of the turbine (<i>Thp</i>) (&gt;= 0). Typical value = 0,15.

Reheater time constant of the turbine (<i>Trh</i>) (&gt;= 0). Typical value = 10.

Low pressure (LP) time constant of the turbine (<i>Tmp</i>) (&gt;= 0). Typical value = 0,4.

Derivative time constant of pressure regulator (<i>Tdc</i>) (&gt;= 0). Typical value = 90.

Time constant of fuel regulation (<i>Tf1</i>) (&gt;= 0). Typical value = 10.

Time constant of steam chest (<i>Tf2</i>) (&gt;= 0). Typical value = 10.

Boiler time constant (<i>Tv</i>) (&gt;= 0). Typical value = 60.

Controller lag (<i>T1</i>) (&gt;= 0).

Controller lead compensation (<i>T2</i>) (&gt;= 0).

Governor lag (<i>T3</i>) (&gt; 0).

Delay due to steam inlet volumes associated with steam chest and inlet piping (<i>T4</i>) (&gt;= 0).

Reheater delay including hot and cold leads (<i>T5</i>) (&gt;= 0).

Delay due to IP-LP turbine, crossover pipes and LP end hoods (<i>T6</i>) (&gt;= 0).

Lower power limit (<i>Pmin</i>) (&gt;= 0 and &lt; GovSteamSGO.pmax).

Power transducer time constant (<i>Tpelec</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt; 0). Typical value = 0,02.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 0,8.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt; 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt; 0). Typical value = 0,02.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 0,6.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt; 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt; 0). Typical value = 0,013.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 1,17.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt; 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 10.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt; 0). Typical value = 0,015.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt; 0). Typical value = 0,02.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 0,8.

Excitation control system stabilizer time constant (<i>T</i><i>_F1</i>) (&gt; 0). Typical value = 1.

Excitation control system stabilizer time constant (<i>T</i><i>_F2</i>) (&gt;= 0). Typical value = 1.

Excitation control system stabilizer time constant (<i>T</i><i>_F3</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt;= 0). Typical value = 0,086.

Voltage regulator time constant (<i>T</i><i>_K</i>) (&gt;= 0). Typical value = 0,18.

Voltage regulator time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 9.

Voltage regulator time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 3.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 1.

Exciter field current limiter time constant (<i>T</i><i>_J</i>) (&gt;= 0). Typical value = 0,02.

Exciter field current limiter time constant (<i>T</i><i>_H</i>) (&gt; 0). Typical value = 0,08.

Lag time constant (<i>T</i><i>_DR</i>) (&gt;= 0). Typical value = 0.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 1,1.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt; 0). Typical value = 1.

Lag time constant (<i>T</i><i>_DR</i>) (&gt; 0). Typical value = 0,1.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt;= 0). Typical value = 0.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 1,2.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt; 0). Typical value = 0,06.

Voltage regulator time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 0.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 0,46.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt; 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt; 0). Typical value = 0,01.

Voltage regulator time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 0.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 1,33.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt; 0). Typical value = 0,675.

Rheostat travel time (<i>T</i><i>_RH</i>) (&gt; 0). Typical value = 20.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 0,5.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt; 0). Typical value = 0,2.

Regulator derivative filter time constant (<i>T</i><i>_D</i>) (&gt; 0 if ExcIEEEDC4B.kd &gt; 0). Typical value = 0,01.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 0,8.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 10.

Voltage regulator time constant (<i>T</i><i>_B1</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_C1</i>) (&gt;= 0). Typical value = 0.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt; 0). Typical value = 0,15.

Exciter time constant, integration rate associated with exciter control (<i>T</i><i>_E</i>) (&gt; 0). Typical value = 0,5.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 10.

Voltage regulator time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 1.

Forward time constant of inner loop field regulator (<i>T</i><i>_M</i>) (&gt; 0). Typical value = 0,4.

Voltage regulator time constant (<i>T</i><i>_A</i>) (&gt;= 0). Typical value = 0,02.

Firing circuit time constant (<i>T1</i>) (&gt;= 0). Typical value = 0,004.

Regulator lead time constant (<i>T</i><i>_C1</i>) (&gt;= 0). Typical value = 0,8.

Regulator lag time constant (<i>T</i><i>_B1</i>) (&gt;= 0). Typical value = 6.

Regulator lead time constant (<i>T</i><i>_C2</i>) (&gt;= 0). Typical value = 0,08.

Regulator lag time constant (<i>T</i><i>_B2</i>) (&gt;= 0). Typical value = 0,01.

OEL lead time constant (<i>T</i><i>_OC1</i>) (&gt;= 0). Typical value = 0,1.

OEL lag time constant (<i>T</i><i>_OB1</i>) (&gt;= 0). Typical value = 2.

OEL lead time constant (<i>T</i><i>_OC2</i>) (&gt;= 0). Typical value = 0,08.

OEL lag time constant (<i>T</i><i>_OB2</i>) (&gt;= 0). Typical value = 0,08.

UEL lead time constant (<i>T</i><i>_UC1</i>) (&gt;= 0). Typical value = 2.

UEL lag time constant (<i>T</i><i>_UB1</i>) (&gt;= 0). Typical value = 10.

UEL lead time constant (<i>T</i><i>_UC2</i>) (&gt;= 0). Typical value = 0,1.

UEL lag time constant (<i>T</i><i>_UB2</i>) (&gt;= 0). Typical value = 0,05.

Feedback time constant of inner loop field voltage regulator (<i>T</i><i>_G</i>) (&gt;= 0). Typical value = 0,02.

Regulator lag time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 1.

Regulator lead time constant (<i>T</i><i>_C</i>) (&gt;= 0). Typical value = 1.

Excitation control system stabilizer time constant (<i>T</i><i>_F</i>) (&gt;= 0). Typical value = 1.

Feedback time constant of inner loop field voltage regulator (<i>T</i><i>_G</i>) (&gt;= 0). Typical value = 1.

Feedback time constant (<i>T</i><i>_IA</i>) (&gt;= 0). Typical value = 3.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>T</i><i>_c</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,02.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 0,8.

Excitation control system stabilizer time constant (<i>Tf</i>) (&gt; 0). Typical value = 1.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,02.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 0,6.

Excitation control system stabilizer time constant (<i>Tf</i>) (&gt; 0). Typical value = 1.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0.

Voltage regulator gain (<i>Ka</i>) (&gt; 0). Typical value = 45,62.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 1,17.

Excitation control system stabilizer time constant (<i>Tf</i>) (&gt; 0). Typical value = 1.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 10.

Voltage regulator time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,015.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,02.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 0,8.

Excitation control system stabilizer time constant (<i>Tf1</i>) (&gt; 0). Typical value = 1.

Excitation control system stabilizer time constant (<i>Tf2</i>) (&gt;= 0). Typical value = 0,8.

Excitation control system stabilizer time constant (<i>Tf3</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Ta</i>) (&gt;= 0). Typical value = 0,086.

Voltage regulator time constant (<i>Tk</i>) (&gt;= 0). Typical value = 0,18.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 9.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 3.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 1.

Exciter field current limiter time constant (<i>Tj</i>) (&gt;= 0). Typical value = 0,02.

Exciter field current limiter time constant (<i>Th</i>) (&gt; 0). Typical value = 0,08.

Voltage regulator time constant (<i>Ta</i>) (&gt;= 0). Typical value = 0.

Lag time constant (<i>Tdr</i>) (&gt; 0 if ExcAC8B.kdr &gt; 0). Typical value = 0,1.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 1,2.

Time constant (<i>T</i><i>₃</i>) (&gt;= 0). Typical value = 1,6.

Time constant (<i>T</i><i>₂</i>) (&gt;= 0). Typical value = 0,05.

Time constant (<i>T</i><i>₁</i>) (&gt;= 0). Typical value = 20.

Exciter time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 0,04.

AVR time constant (<i>T</i><i>_A</i>) (&gt;= 0). Typical value = 0,2.

AVR time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 0.

Exciter time constant (<i>T</i><i>_E</i>) (&gt;= 0). Typical value = 1.

Rate feedback time constant (<i>T</i><i>_F</i>) (&gt;= 0). Typical value = 1.

AVR time constant (<i>T</i><i>_A</i>) (&gt;= 0). Typical value = 0,02.

AVR time constant (<i>T</i><i>_B</i>) (&gt;= 0). Typical value = 0.

Exciter time constant (<i>T</i><i>_E</i>) (&gt;= 0). Typical value = 1.

Rate feedback time constant (<i>T</i><i>_F1</i>) (&gt;= 0). Typical value = 1.

Rate feedback time constant (<i>T</i><i>_F2</i>) (&gt;= 0). Typical value = 1.

AVR time constant (<i>T</i><i>₁</i>) (&gt;= 0). Typical value = 20.

AVR time constant (<i>T</i><i>₂</i>) (&gt;= 0). Typical value = 1,6.

AVR time constant (<i>T</i><i>₃</i>) (&gt;= 0). Typical value = 0,66.

AVR time constant (<i>T</i><i>₄</i>) (&gt;= 0). Typical value = 0,07.

Exciter time constant (<i>T</i><i>_E</i>) (&gt;= 0). Typical value = 1.

AVR time constant (<i>T</i><i>₁</i>) (&gt;= 0). Typical value = 4,8.

AVR time constant (<i>T</i><i>₂</i>) (&gt;= 0). Typical value = 1,5.

AVR time constant (<i>T</i><i>₃</i>) (&gt;= 0). Typical value = 0.

AVR time constant (<i>T</i><i>₄</i>) (&gt;= 0). Typical value = 0.

Exciter current feedback time constant (<i>T</i><i>_IF</i>) (&gt;= 0). Typical value = 0.

Exciter current feedback time constant (<i>T</i><i>_1IF</i>) (&gt;= 0). Typical value = 60.

Time constant (<i>Ta</i>) (&gt;= 0).

Lead time constant (<i>T</i><i>₁</i>) (&gt;= 0). Typical value = 0,05.

Lag time constant (<i>T</i><i>₂</i>) (&gt;= 0). Typical value = 0,1.

Lead time constant (<i>T</i><i>₃</i>) (&gt;= 0). Typical value = 0,1.

Lag time constant (<i>T</i><i>₄</i>) (&gt;= 0). Typical value = 0,1.

Lead time constant (<i>T</i><i>₅</i>) (&gt;= 0). Typical value = 0,1.

Lag time constant (<i>T</i><i>₆</i>) (&gt;= 0). Typical value = 0,1.

Controller time constant (<i>T1</i>) (&gt;= 0). Typical value = 6.

Controller time constant (<i>T2</i>) (&gt;= 0). Typical value = 1.

Lead/lag time constant (<i>T3</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0,05.

Lead/lag time constant (<i>T4</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0,01.

Regulator integral time constant (<i>Tc</i>) (&gt;= 0).

Regulator time constant (<i>Ta</i>) (&gt;= 0).

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt;= 0).

Voltage regulator time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,06.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 0,46.

Excitation control system stabilizer time constant (<i>Tf</i>) (&gt; 0). Typical value = 1.

Voltage regulator time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,01.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 1,33.

Excitation control system stabilizer time constant (<i>Tf</i>) (&gt; 0). Typical value = 0,675.

Excitation control system stabilizer time constant (<i>Tf1</i>) (&gt;= 0). Typical value = 0.

Rheostat travel time (<i>Trh</i>) (&gt; 0). Typical value = 20.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 1,83.

Voltage regulator time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,01.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 1,83.

Excitation control system stabilizer time constant (<i>Tf</i>) (&gt;= 0). Typical value = 0,675.

Current transducer time constant (<i>Tfi</i>) (&gt;= 0). Typical value = 0.

Controller reset time constant (<i>Tnu</i>) (&gt;= 0). Typical value = 2.

Stabilizer parameters (<i>Tsw</i>) (&gt;= 0). Typical value = 3.

Stabilizer phase lag time constant (<i>Ts1</i>) (&gt;= 0). Typical value = 1.

Stabilizer filter time constant (<i>Ts2</i>) (&gt;= 0). Typical value = 1.

Voltage controller derivative washout time constant (<i>Tb1</i>) (&gt;= 0). Typical value = 12,45.

Time constant (<i>Te</i>) (&gt;= 0). Typical value = 0.

Time Constant (<i>T</i><i>_e2</i>) (&gt;= 0). Typical value = 1.

Time constant (<i>T</i><i>_r4</i>) (&gt;= 0). Typical value = 1.

Time constant (<i>T</i><i>_i3</i>) (&gt;= 0). Typical value = 3.

Time constant (<i>T</i><i>_i4</i>) (&gt;= 0). Typical value = 0.

Filter time constant (<i>Tr</i>) (&gt;= 0). If a voltage compensator is used in conjunction with this excitation system model, <i>Tr </i>should be set to 0. Typical value = 0,01.

Major loop PI tag integration time constant (<i>Te</i>) (&gt;= 0). Typical value = 0,154.

Minor loop PI control tag integration time constant (<i>Ti</i>) (&gt;= 0). Typical value = 0,01333.

Time constant (<i>Tr</i>) (&gt;= 0). Typical value = 0,02.

Voltage regulator time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,02.

Excitation control system stabilizer time constant (<i>Tf2</i>) (&gt; 0). Typical value = 0,1.

Excitation control system stabilizer time constant (<i>Tf1</i>) (&gt; 0). Typical value = 1,0.

Time constant (<i>T</i><i>₁</i>) (&gt;= 0).

Time constant (<i>T</i><i>₂</i>) (&gt;= 0).

Time constant (<i>T</i><i>₃</i>) (&gt;= 0).

Time constant (<i>T</i><i>₄</i>) (&gt;= 0).

Time constant (<i>T</i><i>₅</i>) (&gt;= 0).

Time constant (<i>T</i><i>₆</i>) (&gt;= 0).

Time constant (<i>T</i><i>_E</i>) (&gt;= 0).

Time constant (<i>T</i><i>_F</i>) (&gt;= 0).

PI controller time constant (<i>T</i><i>_a1</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>T</i><i>_a2</i>) (&gt;= 0). Typical value = 0,01.

Lead time constant (<i>T</i><i>_a3</i>) (&gt;= 0). Typical value = 0.

Lag time constant (<i>T</i><i>_a4</i>) (&gt;= 0). Typical value = 0.

Rate feedback time constant (<i>T</i><i>_f1</i>) (&gt;= 0). Typical value = 0.

Rate feedback lag time constant (<i>T</i><i>_f2</i>) (&gt;= 0). Typical value = 0.

Exciter time constant (<i>T</i><i>_e</i>) (&gt;= 0). Typical value = 0.

Rate feedback gain (<i>Kf</i>) (&gt;= 0). Typical value = 0,05.

Voltage regulator time constant (<i>Ta</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0,01.

Lag time constant (<i>Tb1</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0.

Lag time constant (<i>Tb2</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0.

Lead time constant (<i>Tc1</i>) (&gt;= 0). Typical value = 0.

Lead time constant (<i>Tc2</i>) (&gt;= 0). Typical value = 0.

Exciter field time constant (<i>Te</i>) (&gt; 0). Typical value = 1,2.

Rate feedback time constant (<i>Tf</i>) (&gt;= 0). If = 0, the feedback path is not used. Typical value = 1.

Feedback lead time constant (<i>Tf1</i>) (&gt;= 0). Typical value = 0.

Feedback lag time constant (<i>Tf2</i>) (&gt;= 0). If = 0, block is bypassed. Typical value = 0.

Field current bridge time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0.

Lead lag time constant (<i>TE</i>) (&gt;= 0). Typical value = 0,22.

Lead lag time constant (<i>TC</i>) (&gt;= 0). Typical value = 0,02.

Voltage input time constant (<i>MESU</i>) (&gt;= 0). Typical value = 0,02.

Input time constant (<i>T4M</i>) (&gt;= 0). Typical value = 5.

Exciter time constant (<i>TF</i>) (&gt;= 0). Typical value = 0,01.

Denominator time constant of lag-lead block (<i>Tb</i>) (&gt;= 0). Typical value = 10.

Time constant of gain block (<i>Te</i>) (&gt; 0). Typical value = 0,02.

Denominator time constant of lag-lead block (<i>Tb</i>) (&gt;= 0). Typical value = 10.

Time constant of gain block (<i>Te</i>) (&gt; 0). Typical value = 0,05.

PI controller phase lead time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0.

PI controller phase lead time constant (<i>Tc</i>) (&gt;= 0). Typical value = 8.

Time constant of gain block (<i>Te</i>) (&gt;= 0). Typical value = 0,1.

PI controller phase lead time constant (<i>Ti</i>) (&gt;= 0). Typical value = 2.

Time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0,1.

Voltage transducer time constant (<i>Tr</i>) (&gt;= 0). Typical value = 0,01.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 10.

Voltage regulator time constant (<i>Ta</i>) (&gt;= 0). Typical value = 0,02.

Excitation control system stabilizer time constant (<i>Tf</i>) (&gt;= 0). Typical value = 1.

Voltage regulator time constant (<i>Tc1</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Tb1</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Ta</i>) (&gt; 0). Typical value = 0,15.

Exciter time constant, integration rate associated with exciter control (<i>Te</i>) (&gt; 0). Typical value = 0,5.

Excitation control system stabilizer time constant (<i>Tf</i>) (&gt;= 0). Typical value = 0,7.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0.

Voltage regulator time constant (<i>Tb</i>) (&gt;= 0). Typical value = 6,67.

Voltage regulator time constant (<i>Tc</i>) (&gt;= 0). Typical value = 1.

Forward time constant of inner loop field regulator (<i>Tm</i>) (&gt; 0). Typical value = 1.

Voltage regulator time constant (<i>Ta</i>) (&gt;= 0). Typical value = 0,02.

Feedback time constant of inner loop field voltage regulator (<i>Tg</i>) (&gt;= 0). Typical value = 0,02.

Rectifier firing time constant (<i>Ts</i>) (&gt;= 0). Typical value = 0.

Voltage regulator derivative gain (<i>Tvd</i>) (&gt;= 0). Typical value = 0.

Regulator lag time constant (<i>Tb</i>) (&gt;= 0). Typical value = 1.

Regulator lead time constant (<i>Tc</i>) (&gt;= 0). Typical value = 1.

Excitation control system stabilizer time constant (<i>Tf</i>) (&gt;= 0). Typical value = 1.

Feedback time constant of inner loop field voltage regulator (<i>Tg</i>) (&gt;= 0). Typical value = 1.

Feedback time constant (<i>Tia</i>) (&gt;= 0). Typical value = 3.

Rectifier firing time constant (<i>Ts</i>) (&gt;= 0). Typical value = 0.

Time to trip the exciter at the low voltage point on the inverse time characteristic (<i>TIME</i><i>₁</i>) (&gt;= 0). Typical value = 120.

Time to trip the exciter at the mid voltage point on the inverse time characteristic (<i>TIME</i><i>₂</i>) (&gt;= 0). Typical value = 40.

Time to trip the exciter at the high voltage point on the inverse time characteristic (<i>TIME</i><i>₃</i>) (&gt;= 0). Typical value = 15.

Time to trip the exciter at the low voltage or current point on the inverse time characteristic (<i>TIME</i><i>₁</i>) (&gt;= 0). Typical value = 120.

Time to trip the exciter at the mid voltage or current point on the inverse time characteristic (<i>TIME</i><i>₂</i>) (&gt;= 0). Typical value = 40.

Time to trip the exciter at the high voltage or current point on the inverse time characteristic (<i>TIME</i><i>₃</i>) (&gt;= 0). Typical value = 15.

UEL lead time constant (<i>T</i><i>_U1</i>) (&gt;= 0). Typical value = 0.

UEL lag time constant (<i>T</i><i>_U2</i>) (&gt;= 0). Typical value = 0,05.

UEL lead time constant (<i>T</i><i>_U3</i>) (&gt;= 0). Typical value = 0.

UEL lag time constant (<i>T</i><i>_U4</i>) (&gt;= 0). Typical value = 0.

Voltage filter time constant (<i>T</i><i>_UV</i>) (&gt;= 0). Typical value = 5.

Real power filter time constant (<i>T</i><i>_UP</i>) (&gt;= 0). Typical value = 5.

Reactive power filter time constant (<i>T</i><i>_UQ</i>) (&gt;= 0). Typical value = 0.

Time constant associated with optional integrator feedback input signal to UEL (<i>T</i><i>_UL</i>) (&gt;= 0). Typical value = 0.

UEL lead time constant (<i>T</i><i>_U1</i>) (&gt;= 0). Typical value = 0.

UEL lag time constant (<i>T</i><i>_U2</i>) (&gt;= 0). Typical value = 0.

UEL lead time constant (<i>T</i><i>_U3</i>) (&gt;= 0). Typical value = 0.

UEL lag time constant (<i>T</i><i>_U4</i>) (&gt;= 0). Typical value = 0.

Differential time constant (<i>T</i><i>_F2</i>) (&gt;= 0).

Minimum excitation limit time constant (<i>T</i><i>_M</i>) (&gt;= 0).

Differential time constant (<i>T</i><i>_F2</i>) (&gt;= 0).

Minimum excitation limit time constant (<i>T</i><i>_M</i>) (&gt;= 0).

Lead/lag time constant (<i>T1</i>) (&gt;= 0). Typical value = 0,3.

Lead/lag time constant (<i>T2</i>) (&gt;= 0). Typical value = 0,03.

Lead/lag time constant (<i>T3</i>) (&gt;= 0). Typical value = 0,3.

Lead/lag time constant (<i>T4</i>) (&gt;= 0). Typical value = 0,03.

Washout time constant (<i>T5</i>) (&gt;= 0). Typical value = 10.

Transducer time constant (<i>T6</i>) (&gt;= 0). Typical value = 0,01.

First washout on signal #1 (<i>Tw1</i>) (&gt;= 0). Typical value = 2.

Second washout on signal #1 (<i>Tw2</i>) (&gt;= 0). Typical value = 2.

First washout on signal #2 (<i>Tw3</i>) (&gt;= 0). Typical value = 2.

Second washout on signal #2 (<i>Tw4</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (<i>T1</i>) (&gt;= 0). Typical value = 0,12.

Lead/lag time constant (<i>T2</i>) (&gt;= 0). Typical value = 0,02.

Lead/lag time constant (<i>T3</i>) (&gt;= 0). Typical value = 0,3.

Lead/lag time constant (<i>T4</i>) (&gt;= 0). Typical value = 0,02.

Time constant on signal #1 (<i>T6</i>) (&gt;= 0). Typical value = 0.

Time constant on signal #2 (<i>T7</i>) (&gt;= 0). Typical value = 2.

Lead of ramp tracking filter (<i>T8</i>) (&gt;= 0). Typical value = 0,2.

Lag of ramp tracking filter (<i>T9</i>) (&gt;= 0). Typical value = 0,1.

Lead/lag time constant (<i>T10</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (<i>T11</i>) (&gt;= 0). Typical value = 0.

Transducer time constant (<i>T1</i>) (&gt;= 0). Typical value = 0,012.

Transducer time constant (<i>T2</i>) (&gt;= 0). Typical value = 0,012.

Washout time constant (<i>Tw1</i>) (&gt;= 0). Typical value = 0,3.

Washout time constant (<i>Tw2</i>) (&gt;= 0). Typical value = 0,3.

Washout time constant (<i>Tw3</i>) (&gt;= 0). Typical value = 0,6.

High band time constant (<i>T</i><i>_H1</i>) (&gt;= 0). Typical value = 0,01513.

High band time constant (<i>T</i><i>_H10</i>) (&gt;= 0). Typical value = 0.

High band time constant (<i>T</i><i>_H11</i>) (&gt;= 0). Typical value = 0.

High band time constant (<i>T</i><i>_H12</i>) (&gt;= 0). Typical value = 0.

High band time constant (<i>T</i><i>_H2</i>) (&gt;= 0). Typical value = 0,01816.

High band time constant (<i>T</i><i>_H3</i>) (&gt;= 0). Typical value = 0.

High band time constant (<i>T</i><i>_H4</i>) (&gt;= 0). Typical value = 0.

High band time constant (<i>T</i><i>_H5</i>) (&gt;= 0). Typical value = 0.

High band time constant (<i>T</i><i>_H6</i>) (&gt;= 0). Typical value = 0.

High band time constant (<i>T</i><i>_H7</i>) (&gt;= 0). Typical value = 0,01816.

High band time constant (<i>T</i><i>_H8</i>) (&gt;= 0). Typical value = 0,02179.

High band time constant (<i>T</i><i>_H9</i>) (&gt;= 0). Typical value = 0.

Intermediate band time constant (<i>T</i><i>_I1</i>) (&gt;= 0). Typical value = 0,173.

Intermediate band time constant (<i>T</i><i>_I10</i>) (&gt;= 0). Typical value = 0.

Intermediate band time constant (<i>T</i><i>_I11</i>) (&gt;= 0). Typical value = 0.

Intermediate band time constant (<i>T</i><i>_I12</i>) (&gt;= 0). Typical value = 0.

Intermediate band time constant (<i>T</i><i>_I2</i>) (&gt;= 0). Typical value = 0,2075.

Intermediate band time constant (<i>T</i><i>_I3</i>) (&gt;= 0). Typical value = 0.

Intermediate band time constant (<i>T</i><i>_I4</i>) (&gt;= 0). Typical value = 0.

Intermediate band time constant (<i>T</i><i>_I5</i>) (&gt;= 0). Typical value = 0.

Intermediate band time constant (<i>T</i><i>_I6</i>) (&gt;= 0). Typical value = 0.

Intermediate band time constant (<i>T</i><i>_I7</i>) (&gt;= 0). Typical value = 0,2075.

Intermediate band time constant (<i>T</i><i>_I8</i>) (&gt;= 0). Typical value = 0,2491.

Intermediate band time constant (<i>T</i><i>_I9</i>) (&gt;= 0). Typical value = 0.

Low band time constant (<i>T</i><i>_L1</i>) (&gt;= 0). Typical value = 1,73.

Low band time constant (<i>T</i><i>_L10</i>) (&gt;= 0). Typical value = 0.

Low band time constant (<i>T</i><i>_L11</i>) (&gt;= 0). Typical value = 0.

Low band time constant (<i>T</i><i>_L12</i>) (&gt;= 0). Typical value = 0.

Low band time constant (<i>T</i><i>_L2</i>) (&gt;= 0). Typical value = 2,075.

Low band time constant (<i>T</i><i>_L3</i>) (&gt;= 0). Typical value = 0.

Low band time constant (<i>T</i><i>_L4</i>) (&gt;= 0). Typical value = 0.

Low band time constant (<i>T</i><i>_L5</i>) (&gt;= 0). Typical value = 0.

Low band time constant (<i>T</i><i>_L6</i>) (&gt;= 0). Typical value = 0.

Low band time constant (<i>T</i><i>_L7</i>) (&gt;= 0). Typical value = 2,075.

Low band time constant (<i>T</i><i>_L8</i>) (&gt;= 0). Typical value = 2,491.

Low band time constant (<i>T</i><i>_L9</i>) (&gt;= 0). Typical value = 0.

Electric power filter time constant (<i>T</i><i>_PE</i>) (&gt;= 0). Typical value = 0,05.

Washout (<i>T</i><i>₅</i>) (&gt;= 0). Typical value = 3,5.

Filter time constant (<i>T</i><i>₆</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (<i>T</i><i>₇</i>) (&gt;= 0). If = 0, both blocks are bypassed. Typical value = 0.

Lead/lag time constant (<i>T</i><i>₈</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (<i>T</i><i>₉</i>) (&gt;= 0). If = 0, both blocks are bypassed. Typical value = 0.

Lead/lag time constant (<i>T</i><i>₁₀</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (<i>T</i><i>₁</i>) (&gt;= 0).

Lead/lag time constant (<i>T</i><i>₂</i>) (&gt;= 0).

Lead/lag time constant (<i>T</i><i>₃</i>) (&gt;= 0).

Lead/lag time constant (<i>T</i><i>₄</i>) (&gt;= 0).

Washout time constant (<i>T</i><i>₅</i>) (&gt;= 0).

Transducer time constant (<i>T</i><i>₆</i>) (&gt;= 0).

Time constant (<i>Tdelay</i>) (&gt;= 0).

First washout on signal #1 (<i>T</i><i>_w1</i>) (&gt;= 0). Typical value = 2.

Second washout on signal #1 (<i>T</i><i>_w2</i>) (&gt;= 0). Typical value = 2.

First washout on signal #2 (<i>T</i><i>_w3</i>) (&gt;= 0). Typical value = 2.

Second washout on signal #2 (<i>T</i><i>_w4</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (<i>T</i><i>₁</i>) (&gt;= 0). Typical value = 0,12.

Lead/lag time constant (<i>T</i><i>₂</i>) (&gt;= 0). Typical value = 0,02.

Lead/lag time constant (<i>T</i><i>₃</i>) (&gt;= 0). Typical value = 0,3.

Lead/lag time constant (<i>T</i><i>₄</i>) (&gt;= 0). Typical value = 0,02.

Time constant on signal #1 (<i>T</i><i>₆</i>) (&gt;= 0). Typical value = 0.

Time constant on signal #2 (<i>T</i><i>₇</i>) (&gt;= 0). Typical value = 2.

Lead of ramp tracking filter (<i>T</i><i>₈</i>) (&gt;= 0). Typical value = 0,2.

Lag of ramp tracking filter (<i>T</i><i>₉</i>) (&gt;= 0). Typical value = 0,1.

Lead/lag time constant (<i>T</i><i>₁₀</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (<i>T</i><i>₁₁</i>) (&gt;= 0). Typical value = 0.

Lead constant (<i>T</i><i>_a</i>) (&gt;= 0). Typical value = 0.

Lag time constant (<i>T</i><i>_b</i>) (&gt;= 0). Typical value = 0.

Time constant (<i>T</i><i>₁</i>) (&gt;= 0).

Time constant (<i>T</i><i>₂</i>) (&gt;= 0).

Time constant (<i>T</i><i>₃</i>) (&gt;= 0).

Time constant (<i>T</i><i>₄</i>) (&gt;= 0).

Time constant (<i>T</i><i>₅</i>) (&gt;= 0).

Time constant (<i>T</i><i>₆</i>) (&gt;= 0).

Time constant (<i>T</i><i>₇</i>) (&gt;= 0).

Time constant (<i>T</i><i>₈</i>) (&gt;= 0).

Time constant (<i>T</i><i>₉</i>) (&gt;= 0).

Time constant (<i>T</i><i>₁₀</i>) (&gt;= 0).

First washout (<i>T</i><i>_W1</i>) (&gt;= 0). Typical value = 3,5.

Second washout (<i>T</i><i>_W2</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (<i>T</i><i>_L1</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (<i>T</i><i>_L2</i>) (&gt;= 0). If = 0, both blocks are bypassed. Typical value = 0.

Lead/lag time constant (<i>T</i><i>_L3</i>) (&gt;= 0). Typical value = 0.

Lead/lag time constant (T_L4) (&gt;= 0). If = 0, both blocks are bypassed. Typical value = 0.

Electric power filter time constant (<i>T</i><i>_PE</i>) (&gt;= 0). Typical value = 0,05.

Time constant (<i>Ts1</i>) (&gt;= 0). Typical value = 0.

Time constant (<i>Ts2</i>) (&gt;= 0). Typical value = 1.

Time constant (<i>Ts3</i>) (&gt;= 0). Typical value = 1.

Time constant (<i>Ts4</i>) (&gt;= 0). Typical value = 0,1.

Time constant (<i>Ts5</i>) (&gt;= 0). Typical value = 0.

Time constant (<i>Ts6</i>) (&gt;= 0). Typical value = 1.

Time constant (<i>Tf</i>) (&gt;= 0). Typical value = 0,2.

Time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0,2.

Time constant (<i>T1</i>) (&gt;= 0). Typical value = 0,3.

Time constant (<i>T2</i>) (&gt;= 0). Typical value = 1.

Time constant (<i>T3</i>) (&gt;= 0). Typical value = 0,2.

Time constant (<i>T4</i>) (&gt;= 0). Typical value = 0,05.

Time step frequency calculation (<i>deltatf</i>) (&gt;= 0). Typical value = 0,025.

Time step related to activation of controls (<i>deltatc</i>) (&gt;= 0). Typical value = 0,025.

Time step active power calculation (<i>deltatp</i>) (&gt;= 0). Typical value = 0,0125.

Time constant (<i>Tf</i>) (&gt;= 0). Typical value = 0,2.

Time constant (<i>Tp</i>) (&gt;= 0). Typical value = 0,2.

Time constant (<i>T1</i>) (&gt;= 0). Typical value = 0,3.

Time constant (<i>T2</i>) (&gt;= 0). Typical value = 1.

Time constant (<i>T3</i>) (&gt;= 0). Typical value = 0,2.

Time constant (<i>T4</i>) (&gt;= 0). Typical value = 0,05.

Time step frequency calculation (<i>deltatf</i>) (&gt;= 0). Typical value = 0,025 (0,03 for 50 Hz).

Time step related to activation of controls (<i>deltatc</i>) (&gt;= 0). Typical value = 0,025 (0,03 for 50 Hz).

Time step active power calculation (<i>deltatp</i>) (&gt;= 0). Typical value = 0,0125 (0,015 for 50 Hz).

Time constant (<i>T5</i>) (&gt;= 0).

Time constant (<i>T6</i>) (&gt;= 0).

Input time constant (<i>T4M</i>) (&gt;= 0). Typical value = 5.

Speed delay (<i>TOMD</i>) (&gt;= 0). Typical value = 0,02.

Speed time constant (<i>TOMSL</i>) (&gt;= 0). Typical value = 0,04.

Speed time constant (<i>T4MOM</i>) (&gt;= 0). Typical value = 1,27.

Lead lag time constant (<i>T4F</i>) (&gt;= 0). Typical value = 0,045.

Time constant (<i>Tt</i>) (&gt;= 0). Typical value = 0,18.

Time constant (<i>Tx2</i>) (&gt;= 0). Typical value = 5,0.

Time constant (<i>Ta</i>) (&gt;= 0). Typical value = 0,37.

Reset time constant (<i>Tx1</i>) (&gt;= 0). Typical value = 0,035.

Time constant (<i>Tb</i>) (&gt;= 0). Typical value = 0,37.

Time constant (<i>Tc</i>) (&gt;= 0). Typical value = 0,035.

Time constant (<i>Td</i>) (&gt;= 0). Typical value = 0,0.

Time constant (<i>Te</i>) (&gt;= 0). Typical value = 0,0169.

Input time constant (<i>T</i><i>_d</i>) (&gt;= 0). Typical value = 10.

Time constant 1 (<i>T1</i>) (&gt; 0). Typical value = 0,076.

Time constant 2 (<i>T2</i>) (&gt; 0). Typical value = 0,086.

Time constant 3 (<i>T3</i>) (&gt; 0). Typical value = 1,068.

Time constant 4 (<i>T4</i>) (&gt; 0). Typical value = 1,913.

Denominator time constant (<i>T</i><i>₁</i>) (&gt; 0,005). Typical value = 0,3.

Filter time constant (<i>T</i><i>₂</i>) (&gt; 0,005). Typical value = 0,35.

Denominator time constant (<i>T</i><i>₃</i>) (&gt; 0,005). Typical value = 0,22.

Filter time constant (<i>T</i><i>₄</i>) (&gt; 0,005). Typical value = 0,02.

Denominator time constant (<i>T</i><i>₅</i>) (&gt; 0,005). Typical value = 0,02.

Filter time constant (<i>T</i><i>₆</i>) (&gt; 0,005). Typical value = 0,02.

Time constant (<i>T2</i>). Typical value = 4,0.

Time constant (<i>T3</i>). Typical value = 2,0.

Time constant (<i>T5</i>). Typical value = 4,5.

Input signal 1 transducer time constant (<i>T</i><i>₁</i>) (&gt;= 0). Typical value = 0,037.

Input signal 2 transducer time constant (<i>T</i><i>₂</i>) (&gt;= 0). Typical value = 0,0.

Stabilizer washout time constant (<i>T</i><i>₃</i>) (&gt;= 0). Typical value = 9,5.

Stabilizer washout time lag constant (<i>T</i><i>₄</i>) (&gt;= 0). Typical value = 9,5.

Lead time constant (<i>T</i><i>₅</i>) (&gt;= 0). Typical value = 1,7.

Lag time constant (<i>T</i><i>₆</i>) (&gt;= 0). Typical value = 1,5.

Lead time constant (<i>T</i><i>₇</i>) (&gt;= 0). Typical value = 1,7.

Lag time constant (<i>T</i><i>₈</i>) (&gt;= 0). Typical value = 1,5.

Lag time constant (<i>T</i><i>₁₀</i>) (&gt;= 0). Typical value = 0.

Lead time constant (<i>T</i><i>₉</i>) (&gt;= 0). Typical value = 0.

Discontinuous controller time constant (<i>T</i><i>_AN</i>) (&gt;= 0). Typical value = 0,08.

DEC washout time constant (<i>T</i><i>_W</i>₅) (&gt;= 0). Typical value = 5.

Time constant (<i>T</i><i>_D</i>) (&gt;= 0). Typical value = 0,03.

Time constant (<i>T</i><i>_L</i>₁) (&gt;= 0). Typical value = 0,025.

Time constant (<i>T</i><i>_L</i>₂) (&gt;= 0). Typical value = 1,25.

Discontinuous controller time constant (<i>T</i><i>_D1</i>) (&gt;= 0).

Discontinuous controller washout time constant (<i>T</i><i>_D2</i>) (&gt;= 0).

Reset time delay (<i>T</i><i>_DR</i>) (&gt;= 0).

PF controller time delay (<i>T</i><i>_PFC</i>) (&gt;= 0). Typical value = 5.

Var controller time delay (<i>T</i><i>_VARC</i>) (&gt;= 0). Typical value = 5.

Time that adjuster pulses are on (<i>T</i><i>_AON</i>) (&gt;= 0). Typical value = 0,1.

Time that adjuster pulses are off (<i>T</i><i>_AOFF</i>) (&gt;= 0). Typical value = 0,5.

<font color="#0f0f0f">Time constant which is used for the combined voltage sensing and compensation signal (<i>Tr</i>) (&gt;= 0).</font>

<font color="#0f0f0f">Time constant which is used for the combined voltage sensing and compensation signal (<i>Tr</i>) (&gt;= 0).</font>

Voltage measurement filter time constant (<i>T</i><i>_ufiltcl</i>) (&gt;= 0). It is a type-dependent parameter.

Pitch time constant (<i>ttheta</i>) (&gt;= 0). It is a type-dependent parameter.

Timedelay after deep voltage sags (<i>T</i><i>_DVS</i>) (&gt;= 0). It is a project-dependent parameter.

Filter time constant for generator speed measurement (<i>T</i>_omegafiltp3) (&gt;= 0). It is a type-dependent parameter.

Filter time constant for power measurement (<i>T</i>_pfiltp3) (&gt;= 0). It is a type-dependent parameter.

Filter time constant for voltage measurement (<i>T</i>_ufiltp3) (&gt;= 0). It is a type-dependent parameter.

Time constant in speed reference filter (<i>T</i>_omega,ref) (&gt;= 0). It is a type-dependent parameter.

Time constant in power order lag (<i>T</i><i>_pordp4A</i>) (&gt;= 0). It is a type-dependent parameter.

Voltage measurement filter time constant (<i>T</i><i>_ufiltp4A</i>) (&gt;= 0). It is a type-dependent parameter.

Time constant in aerodynamic power response (<i>T</i><i>_paero</i>) (&gt;= 0). It is a type-dependent parameter.

Time constant in power order lag (<i>T</i><i>_pordp4B</i>) (&gt;= 0). It is a type-dependent parameter.

Voltage measurement filter time constant (<i>T</i><i>_ufiltp4B</i>) (&gt;= 0). It is a type-dependent parameter.

Power measurement filter time constant (<i>T</i><i>_pfiltq</i>) (&gt;= 0). It is a type-dependent parameter.

Voltage measurement filter time constant (<i>T</i><i>_ufiltq</i>) (&gt;= 0). It is a type-dependent parameter.

Length of time period where post fault reactive power is injected (<i>T</i><i>_post</i>) (&gt;= 0). It is a project-dependent parameter.

Time constant in reactive power order lag (<i>T</i><i>_qord</i>) (&gt;= 0). It is a type-dependent parameter.

Power measurement filter time constant for Q capacity (<i>T</i><i>_pfiltql</i>) (&gt;= 0). It is a type-dependent parameter.

Voltage measurement filter time constant for Q capacity (<i>T</i><i>_ufiltql</i>) (&gt;= 0). It is a type-dependent parameter.

Filter time constant for generator speed measurement (<i>T</i><i>_omegafiltrr</i>) (&gt;= 0). It is a type-dependent parameter.

Filter time constant for power measurement (<i>T</i><i>_pfiltrr</i>) (&gt;= 0). It is a type-dependent parameter.

Lead time constant in reference value transfer function (<i>T</i><i>_pft</i>) (&gt;= 0). It is a project-dependent parameter.

Lag time constant in reference value transfer function (<i>T</i><i>_pfv</i>) (&gt;= 0). It is a project-dependent parameter.

Filter time constant for frequency measurement (<i>T</i><i>_WPffiltp</i>) (&gt;= 0). It is a project-dependent parameter.

Filter time constant for active power measurement (<i>T</i><i>_WPpfiltp</i>) (&gt;= 0). It is a project-dependent parameter.

Time interval of moving average window (<i>TfMA</i>) (&gt;= 0). It is a type-dependent parameter.

Filter time constant for voltage-dependent reactive power (<i>T</i><i>_uqfilt</i>) (&gt;= 0). It is a project-dependent parameter.

Filter time constant for active power measurement (<i>T</i><i>_WPpfiltq</i>) (&gt;= 0). It is a project-dependent parameter.

Filter time constant for reactive power measurement (<i>T</i><i>_WPqfiltq</i>) (&gt;= 0). It is a project-dependent parameter.

Filter time constant for voltage measurement (<i>T</i><i>_WPufiltq</i>) (&gt;= 0). It is a project-dependent parameter.

Lead time constant in reference value transfer function (<i>T</i><i>_xft</i>) (&gt;= 0). It is a project-dependent parameter.

Lag time constant in reference value transfer function (<i>T</i><i>_xfv</i>) (&gt;= 0). It is a project-dependent parameter.

Current generation time constant (<i>T</i><i>_g</i>) (&gt;= 0). It is a type-dependent parameter.

Time constant for crowbar washout filter (<i>T</i><i>_wo</i>) (&gt;= 0). It is a case-dependent parameter.

Lag time constant (<i>T</i><i>₁</i>) (&gt;= 0). It is a type-dependent parameter.

Voltage measurement time constant (<i>T</i><i>_r</i>) (&gt;= 0). It is a type-dependent parameter.

Current PI controller integration time constant (<i>T</i><i>_Ic</i>) (&gt;= 0). It is a type-dependent parameter.

Time constant (<i>T</i><i>_g</i>) (&gt;= 0). It is a type-dependent parameter.

Inertia constant of generator (<i>H</i><i>_gen</i>) (&gt;= 0). It is a type-dependent parameter.

Inertia constant of wind turbine rotor (<i>H</i><i>_WTR</i>) (&gt;= 0). It is a type-dependent parameter.

Time constant for PLL first order filter model (<i>T</i><i>_PLL</i>) (&gt;= 0). It is a type-dependent parameter.

Inertia constant (<i>H</i>) (&gt;= 0). Typical value = 2,5.

Time constant of lag function of active power (<i>T</i><i>_P</i>) (&gt; 0).

Time constant of lag function of reactive power (<i>T</i><i>_Q</i>) (&gt; 0).

Transient rotor time constant (<i>Tpo</i>) (&gt;= 0). Typical value = 1.

Subtransient rotor time constant (<i>Tppo</i>) (&gt;= 0). Typical value = 0,02.

Inertia constant (<i>H</i>) (&gt;= 0). Typical value = 0,4.

Voltage trip pickup time (<i>Tv</i>) (&gt;= 0). Typical value = 0,1.

Circuit breaker operating time (<i>Tbkr</i>) (&gt;= 0). Typical value = 0,08.

Time it takes to get the unit on-line, from the time that the prime mover mechanical power is applied.

The nominal acceptable duration of the limit. Limits are commonly expressed in terms of the time limit for which the limit is normally acceptable. The actual acceptable duration of a specific limit may depend on other local factors such as temperature or wind speed. The attribute has meaning only if the flag isInfiniteDuration is set to false, hence it shall not be exchanged when isInfiniteDuration is set to true.

The time between each pair of subsequent regular time points in sequence order.